Skip to content

Electrical terms

Definitions stay short. A number appears only when a cited source or the calculator engine produced it.

26 terms

Alternating current

Alternating current (AC) is current that changes direction in a repeating pattern. A sine wave is a common example. AC can have other wave shapes too. Formula...

American Wire Gauge (AWG)

American Wire Gauge (AWG) is a size system based on nominal wire diameter. Within the numbered sequence, a higher gauge number means a smaller diameter. Formul...

Amp-hour

An amp-hour (Ah) is a unit of electric charge, equal to the charge transferred by one ampere sustained for one hour. One Ah equals 3,600 coulombs. Formula For...

Ampacity

Ampacity is how much current a wire can carry without getting too hot. The limit depends on the wire and the conditions where it is used. Formula Ampacity has...

Ampere

An ampere (A), commonly called an amp, is the SI unit of electric current. One ampere corresponds to one coulomb of charge flowing per second. Formula **Avera...

Apparent power

Apparent power is RMS volts times RMS amps for a single-phase AC load. Its unit is the volt-ampere (VA). It differs from real power in watts. Formula **S = V...

Continuous load

A continuous load is one whose maximum current is expected to continue for three hours or more. OSHA's electric-power glossary uses this time-based definition....

Direct current

Direct current (DC) is electric current flowing in one direction. Its magnitude can be steady or can vary without reversing direction. Formula For steady DC,...

Duty cycle

Duty cycle is the fraction of a repeating cycle spent in a specified active state. It is usually expressed as a percentage. Formula **Duty cycle = on-time ÷ p...

Electrical efficiency

Electrical efficiency is useful output divided by input. For a power converter, compare output watts with input watts at the same load. Some input energy become...

Electrical resistance

Electrical resistance is how much a path opposes current. Its unit is the ohm (Ω). A simple resistor links voltage and current through Ohm's law. Formula For...

Equipment grounding conductor

An equipment grounding conductor gives fault current a path back to the supply. It links exposed metal parts to the grounding and bonding system. Formula This...

Inrush current

Inrush current is a short surge of current when equipment is energized or starts operating. Its size and duration depend on the device and the starting conditio...

Inverse-time breaker

An inverse-time breaker trips faster as excess current rises. This describes part of its trip curve. A separate fast trip may act on a large fault. Formula Th...

Kilowatt-hour

A kilowatt-hour (kWh) measures energy. It is the energy used by one kilowatt of power running for one hour. Formula **Energy (kWh) = power (W) × time (h) ÷ 1,...

Nameplate

A nameplate is a product label with its maker, model and ratings. The electrical ratings apply to that model under the conditions shown on the label. Formula...

Ohm

An ohm (Ω) is the SI unit of electrical resistance. One ohm equals one volt per ampere. Formula **R = V ÷ I**, or equivalently **V = I × R**, for an ohmic com...

Peak sun hours

Peak sun hours turn daily solar energy into hours at one kilowatt per square meter. They measure a solar resource. They do not count hours of daylight. Formula...

Power factor

Power factor is real AC power divided by apparent power. It describes how much of the volts-times-amps product corresponds to average power in watts. Formula...

Reactive power

Reactive power describes energy that flows back and forth in an AC circuit. Coils and capacitors store and return this energy. Its unit is var. Formula For th...

RMS voltage

RMS voltage is a way to measure a changing voltage. Across a fixed resistor, it gives the same average heating power as an equal DC voltage. Formula Find RMS...

Starting watts

Starting watts are the power needed for a short time as a device starts. The maker may list this apart from its normal running watts. Formula For one item sta...

Volt

A volt (V) is the SI unit of electric potential difference. One volt corresponds to one joule of energy per coulomb of charge. Formula **Potential difference...

Voltage drop

Voltage drop is the change in voltage across a part or along a current path. For a basic DC resistor, it equals current times resistance. Formula **Voltage dr...

Voltage drop across a resistor

Voltage drop across a resistor is the voltage between its ends. In a basic DC circuit, find it by multiplying current by resistance. Formula **V = I × R**. V...

Watt

A watt (W) is the SI unit of power, the rate at which energy is transferred or converted. One watt equals one joule per second. Formula For steady DC, **P = V...