Digits, multiplier, tolerance
How to use this calculator
- Pick 4, 5, or 6 bands.
- Then pick the color of each band, starting at the end opposite the tolerance band.
- The card shows ohms, the tolerance, and the allowed range.
- Submit the form if JavaScript is off.
- The same tables run on the server, so the first number is already on the page.
The default is a 4 band resistor: brown, black, red, gold. Significant digits are 10. The red multiplier is 100. Resistance is 1000 ohms. Gold is 5 percent. The range is 950 to 1050 ohms. All About Circuits lists that code as 1 kΩ ±5%. You can check it on their calculator with the same four colors.
The first digit cannot be black. Black is zero, and a leading zero is not a valid significant digit on this form. If the first band looks black, you may be reading the resistor from the wrong end. Tolerance is usually gold, silver, or a tighter color set back from the digits. Start at the other end.
Four bands
Band 1 and band 2 are digits. Band 3 is the multiplier. Band 4 is the tolerance. Brown is 1, black is 0, so brown-black is 10. Red as a multiplier is 100. 10 times 100 is 1000 ohms. Gold as a tolerance is 5 percent. 5 percent of 1000 is 50. The low value is 950. The high value is 1050.
Gold as a multiplier is 0.1. Brown, black, gold, gold is 10 times 0.1, which is 1 ohm, still at 5 percent. The range is 0.95 to 1.05 ohms. Silver as a multiplier is 0.01; pink is 0.001. Gold and silver are also supported as tolerances. Digit colors from black through white are powers of ten from 1 through 1,000,000,000.
Red, red, brown, gold is a common 220 ohm, 5 percent part. Digits 22, multiplier 10, product 220. The range is 209 to 231 ohms. Yellow, violet, brown, gold is 470 ohms at 5 percent. Those two codes are in the table at the bottom of this page, with other round 4 band values. Every cell is this engine.
Five and six bands
Five band parts add a third digit. Band 1, 2, and 3 are digits. Band 4 is the multiplier. Band 5 is the tolerance. Brown, black, black, brown, brown is 100 times 10, which is 1000 ohms, at 1 percent. The range is 990 to 1010 ohms. Same nominal 1000 ohms as the default 4 band part, tighter tolerance. Supported tolerance bands are brown 1 percent, red 2 percent, green 0.5 percent, blue 0.25 percent, violet 0.1 percent, gray 0.05 percent, gold 5 percent, and silver 10 percent. The tool does not claim to support every tolerance marking in the standard.
Six band parts use the same ohm math as five band. The sixth band is the temperature coefficient. This page notes that the sixth band is not used in the ohm value and does not decode its ppm figure. The ohms, tolerance, and range are calculated from the first five colors only. Check the exact part datasheet for its temperature coefficient.
Worked example
- Leave the default 4 band code.
- The card reads 1000 ohms at 5 percent.
- Change band 3 from red to brown.
- Digits are still 10.
- The brown multiplier is 10. Resistance is 100 ohms. The range at 5 percent is 95 to 105 ohms. Change band 3 to orange. The orange multiplier is 1000. Resistance is 10000 ohms. Those three rows sit in the table as brown, black, black or brown or red or orange, with gold.
Switch the form to 5 band and keep brown, black, black, brown, brown. The card reads 1000 ohms at 1 percent. Carry 1000 ohms into Ohm's law at 12 volts, solving for amps. That page prints the current from its own engine. This page only reads the color bands. The next-step button starts at 12 volts and the ohms from this card so you do not retype 1000.
Common 4 band codes
Digits, multiplier, gold tolerance. Every cell is computed by the same function as the result card.
| Colors | Ohms |
|---|---|
| brown, black, black, gold | 10 |
| brown, black, brown, gold | 100 |
| brown, black, red, gold | 1000 |
| brown, black, orange, gold | 10000 |
| red, red, brown, gold | 220 |
| red, red, red, gold | 2200 |
| orange, orange, brown, gold | 330 |
| yellow, violet, brown, gold | 470 |
| yellow, violet, orange, gold | 47000 |
| brown, black, yellow, gold | 100000 |
Digits, multipliers, and which end to start from
The supported digit colors run from black 0 through white 9. Pink is an additional multiplier, ×0.001, identified in the current consolidated IEC 60062 edition summary. Gray is supported as a ±0.05 percent tolerance per Vishay's manufacturer chart. The supported set is intentionally limited to the calculator's validated choices and is not a complete IEC table. On six-band mode, the first five bands provide the resistance and tolerance; the sixth temperature-coefficient band is not decoded.
Hold the resistor so the tolerance band is on the right. Read left to right. On a 4 band part that is digit, digit, multiplier, tolerance. On a 5 band part that is digit, digit, digit, multiplier, tolerance. If both ends look like gold, the body is a 5 percent 4 band part and the gold that sits apart from the group of three is the tolerance. If you reverse a 4 band brown-black-red-gold code you get gold, red, black, brown, which is not a valid first digit on this form. The page will fall back to the default instead of inventing a value.
A 1000 ohm resistor at 12 volts is a small DC current on the Ohm's law page. It is not a heater. Stay inside the wattage rating printed on the part. This color-code tool will not warn you about dissipation. That is why the next step is Ohm's law, where watts appear next to ohms.
Common questions
What does brown black red gold mean?
1000 ohms at 5 percent. Digits 10, multiplier 100, gold tolerance. That is the default on this page. The range is 950 to 1050 ohms.
How do I read a 5 band resistor?
Three digits, then multiplier, then tolerance. Brown, black, black, brown, brown is 1000 ohms at 1 percent. The range is 990 to 1010 ohms.
What does the sixth band do?
It is the temperature coefficient. This page does not convert it to ppm. Ohms still come from the first five bands, the same way as a 5 band part.
Why is the first band not allowed to be black?
Black is digit 0. A leading zero is not a significant digit here. If the stripe nearest one end is black, try reading from the other end.
Where does the current come from?
From Ohm's law, using these ohms and the volts you type there. The next-step button starts at 12 volts. Change the volts on that page if your supply is not 12 V.
Limitations
This is a calculation aid, not a permit.
The Ohm's law page starts at 12 volts and these ohms, solving for amps. Use it when you want the current that resistor would draw on a 12 volt DC supply.
It does not pick a resistor wattage rating. Dissipation is volts times amps on the Ohm's law page. It does not read surface-mount number codes. It does not decode 3 band parts. It does not use orange, yellow, or gray as a tolerance color, because those colors are not in both All About Circuits tables this engine cites. If a part uses a tolerance color that is not in the list, this form will reject it and show the default. It does not store what you type. Search engines should use the clean address of this tool.
It is not a substitute for a meter. Paint wears. A gold band can look yellow. If the reading and the meter disagree, the meter wins on a part that is already in a circuit, after you isolate it. Use this page to read a new part from the stripes, then confirm with a meter if the value matters.
The address of a filled-in calculation includes the band count and the color of each band. Search engines should use the clean address of this tool. A filled-in address points its canonical link at the page with no query. The number on the card is the same either way, because the server computes it before any script runs.
Results are rounded to four decimal places. 10 times 100 is 1000. Gold at 5 percent of 1000 is a 50 ohm window. Other multipliers are not whole ohms, especially gold and silver. Keep the assumptions with the number. An ohm figure without the colors and the band count cannot be checked later. Show steps includes those items so a printed page still shows them. The print button hides the menu and the form. The steps stay.
Sources
- IEC 60062:2016, consolidated edition catalogue summary. Accessed 2026-10-18.
- Vishay resistor color code chart. Accessed 2026-10-18.
The supported color mappings are cross-checked against the cited IEC catalogue summary and Vishay chart. The default 4 band code is 1000 ohms at 5 percent.
Cite this page
Wattopedia Editorial Team. Resistor Color Code Calculator. https://wattopedia.com/resistor-color-code-calculator . Updated 2026-10-29.