Skip to content

EV Charger Breaker and Wire Size Calculator

Estimate an EV charger breaker rating and copper wire reference size from nameplate current or AC input power, voltage and run length.

Level 2 single-phase charging is treated as continuous. Use nameplate current where possible; the power-input option assumes power factor 1.

Breaker: 60 A for 48 A continuous charging. Wire: 4 AWG copper. Set by ampacity (4 AWG supports 70 A under the selected source conditions).

CurrentBREAKER
60 A

Breaker rating

Wire: 4 AWG

11.52 kW at power factor 1

Show steps
  1. Calculated minimum = 48 A × 125% = 60 A.
  2. The smallest listed standard rating at or above the unrounded minimum is 60 A.
  3. Required ampacity = 48 A × 125% = 60 A.
  4. Ampacity check: 4 AWG is the first verified size meeting 60 A, including applicable small-conductor limits.
  5. Voltage-drop check: 2 × 25 ft × 48 A × resistance per 1,000 ft / 1,000. The first passing size is 12 AWG.
  6. Choose the larger conductor required by either check: 4 AWG, 0.7253 V drop (0.3022%).
  7. The copper resistance model is corrected to 75 °C and excludes AC reactance and connections. This is a preliminary reference estimate, not installation approval. Verify actual conductor data, equipment terminals, ambient temperature, grouping and applicable installation rules.
  8. Single-phase input at unity power factor: 48 A × 240 V / 1,000 = 11.52 kW. Use the charger nameplate current when available.

Minimum size for this load. Local code and the equipment label take priority.

How to use this calculator

  1. Read the charger input current from its installation instructions.
  2. Select 240 or 208 V and enter the one-way run length.
  3. Calculate to see the continuous-load minimum and next listed breaker rating.
  4. Use a wire result only when both conductor checks are available, and confirm the full installation with a qualified electrician.

Formula

Minimum breaker rating = charger current × 1.25, rounded up to a listed rating.
Conductor size must meet ampacity and voltage-drop requirements independently.

Common charging currents

Continuous charging currentCalculated minimumListed breaker
16 A20 A20 A
24 A30 A30 A
32 A40 A40 A
40 A50 A50 A
48 A60 A60 A
64 A80 A80 A
80 A100 A100 A

Common questions

What breaker does a 48 A charging load need?

The continuous-load calculation is 48 × 125% = 60 A. The next listed rating is 60 A. Check the charger instructions before choosing equipment.

Can input kW replace the charger nameplate current?

Only under the stated unity-power-factor assumption. Charging output, AC input power and current are different ratings. Prefer the manufacturer input-current rating.

Limitations

This is a single-phase, continuous-load model. It does not assess service capacity, load management, installation derating, terminal compatibility, cable restrictions, grounding or fault interruption. Wire selection stays unavailable without verified source data; a breaker result does not verify conductor suitability. No miles-per-hour charging estimate is inferred.

Sources

  1. NFPA 70 Table 240.6(A) (NEC 2023 development record; Table 240.6(A)). Checked 2026-11-18.
  2. Tesla Universal Wall Connector installation manual: circuit breaker rating and maximum output. Checked 2026-11-18.
  3. NBS Handbook 100, Table 5: standard annealed copper resistance at 20 C (1966). Checked 2026-11-19.
  4. Manufacturer copper wire reference facts (Cerrowire and Southwire) (Cerrowire 2017-based reference; Southwire SPEC10000 revision 1.000.113 (2023-based)). Checked 2026-11-19.
  5. Southwire copper conductor product specifications (revision 1.000.113). Checked 2026-11-19.

Cite this page

Wattopedia Editorial Team. EV Charger Breaker and Wire Size Calculator. https://wattopedia.com/ev-charger-breaker-wire-calculator . Updated 2026-10-29.