Skip to content

Electronics · Ideal circuit model

LED resistor calculator

Calculate ideal LED series resistance and resistor power from voltage and current.

Use forward-voltage and current values for the exact LED model. This ideal model covers one series string, not parallel strings or driver losses.

This LED resistor calculator finds an ideal resistor value and power loss for one series string. Enter the supply voltage, the LED's forward voltage and target current from its data sheet, then set the count of LEDs in that string. The result is a math estimate for your inputs, with each step shown for review, but it cannot confirm that any part is safe.

ResistanceIDEAL SERIES RESISTANCE
Enter inputs Ω

Calculated result

Show steps
Total LED forward voltage
Not stated
Resistor voltage
Not stated
Resistor dissipation
Not stated

    Estimate only. Check equipment labels and local code.

    Use model-specific LED values

    The forward voltage field means the voltage drop for one LED at the intended operating current. It is not a universal value for a color or package. Read the exact LED data sheet and use conditions that match the proposed circuit. Forward voltage can vary with device type, current, manufacturer, production lot, and temperature. A typical value may help with an estimate, but it does not establish a worst-case design limit. The current entry is the target current for the string. Do not treat a value copied from another LED, a similar-looking part, or a general web table as confirmation of the selected part's limit. If the data sheet gives a range, this simple tool does not model its full tolerance range. Review the result with the actual component information before using it.

    The model covers one series string

    For a series connection, the same current flows through each LED, and their forward-voltage drops add. The tool multiplies the entered per-device forward voltage by the string count, subtracts that total from the DC supply, and divides the remaining voltage by the target current after converting milliamps to amps. In symbols, R = (Vs − N × Vf) / I. A positive voltage headroom is required; when the supply does not exceed the total LED drop, this model cannot produce a valid positive resistor. This is not a drawing-based circuit solver. It does not accept parallel branches, mixed networks, alternating current, a switching driver, or a regulated current source. Do not put separate parallel strings into one series count. Each real branch can have different current sharing and needs its own design analysis.

    Resistance and dissipation are different outputs

    The resistance is the ideal value required by the entered assumptions. The tool also calculates resistor dissipation from the modeled current and voltage drop, using P = I²R. Dissipation describes heat converted by the model; it is not the resistor's power rating. A practical part choice depends on its data sheet, ambient temperature, board and enclosure conditions, pulse behavior, tolerances, and the complete circuit. This tool does not select a stocked resistance, round to a preferred series, add a blanket margin, or check a part's temperature derating. It therefore cannot say that a particular resistor will run cool or remain within its limit. Use the dissipation as one design input, then check the actual resistor specification and relevant thermal conditions. The result also says nothing about the LED's maximum current or optical performance.

    Check the surrounding electrical quantities

    An Ohm's law calculator can help inspect the relationship among voltage, current, and resistance, while a power calculator can show the electrical power relationship. A resistor color code tool answers a different question: it reads a marked component value, not whether that component is suitable for this LED circuit. Keep these tasks separate. Record the LED part number, its data-sheet conditions, the supply range, and the assumptions used for the estimate. Recalculate when any of those inputs change. If the supply is only a nominal label and can vary, the nominal calculation alone is not a complete check. The answer here is deliberately narrow: it is the result of the selected ideal series-string model, with its inputs visible so that another person can review them.

    Keep a useful design record

    A result is easier to review when its assumptions stay beside it. Note the exact LED part, the source and conditions for its forward-voltage value, the target current, and the supply range used for the estimate. Write down whether the supply is regulated and whether the circuit includes a driver. If another person reviews the calculation, they can see which model was used and which checks are still open. This record does not make the design safe by itself. It reduces the chance that a nominal value is reused after the part or supply changes. Revisit the calculation when the LED data, string layout, or operating conditions change. Keep circuit calculations separate from a final part approval and follow the component maker's guidance.

    Worked examples

    SupplyLED modelSeries countTarget currentIdeal RDissipation
    5 V2 V120 mA150 Ω0.06 W
    12 V3.2 V220 mA280 Ω0.112 W
    9 V2.1 V320 mA135 Ω0.054 W
    5 V2 V210 mA100 Ω0.01 W
    24 V3.2 V4350 mA32 Ω3.92 W

    Common questions

    Does this choose a safe resistor wattage?

    No. It reports modeled dissipation only. Check the exact resistor data sheet, ambient and board conditions, and derating information before choosing a part.

    Can I enter parallel LED strings?

    No. The calculation covers one series string. It does not model current sharing or separate parallel branches.

    Why use the exact LED forward voltage?

    Forward voltage varies by LED model and operating conditions. Use the exact part's data sheet and do not assume a color name gives a fixed value.

    What if the supply is below the total LED drop?

    The model requires positive resistor voltage. If the supply does not exceed the summed LED drops, it rejects the input rather than inventing a resistor value.

    Limitations

    Calculated resistance and dissipation only; not a component-rating recommendation.

    More electronics tools

    Limits of this ideal calculation

    The equation assumes a steady DC supply, an ideal resistor, and the entered LED drops. It omits supply variation, resistor tolerance, wiring loss, driver output resistance, startup behavior, transients, thermal coupling, and changes in LED voltage with operating conditions. A driver-specific equation may include a switch or output-resistance term. For example, Texas Instruments documents such a term for its named lighting driver; that component is not included in this simplified calculator. A calculation that omits it must not be presented as the manufacturer's complete design method. If the circuit has a current regulator, a long cable, multiple branches, a changing supply, or safety-critical use, use a suitable circuit analysis and the exact device documentation instead. This page is educational and does not replace engineering review.

    Sources

    1. Texas Instruments AN-1293, Driving RGB LED Using LP3936 Lighting Management System
    2. OpenStax University Physics Volume 2, §9.5 Electrical Energy and Power

    Related tools

    Cite this page

    Wattopedia Editorial Team. LED resistor calculator. https://wattopedia.com/led-resistor-calculator . Updated 2026-10-29.