The kW to kVA relationship
Kilowatts describe real power, the part of electrical power converted to useful work, heat, light, or motion. Kilovolt-amperes describe apparent power, which reflects voltage and current together. In an AC system the two values may differ because voltage and current waveforms can be out of phase or distorted. Power factor expresses the ratio of real power to apparent power for the stated measurement conditions. The conversion therefore divides the kW value by power factor. A lower power factor produces a larger kVA result for the same real power. The displayed answer is rounded for readability; keep the input and formula visible when comparing it with a nameplate or specification. This calculator uses the scalar power-factor model in its reference sources. It does not inspect harmonics, waveform quality, phase balance, motor starting, or changing loads. Use data that describes the same operating condition and electrical system. If a data sheet gives only kW, do not assume a power factor simply to obtain kVA. Find the specified or measured value, or ask a qualified person familiar with the equipment.
Enter a valid power factor
Power factor is entered as a decimal greater than zero and no greater than one. Use the value associated with the real-power input, not a generic value copied from another load. A motor, electronic power supply, lighting system, and mixed facility can have different power-factor behavior. The value may also vary with operating level and measurement method. If the source gives a percentage, convert it to a decimal before entering it. For example, a source value of eighty percent is entered as 0.8. That illustration explains notation only; it is not a recommended assumption for your equipment. The calculator rejects a missing, zero, negative, or above-one value because each would make this simple relation invalid for its stated purpose. A very small valid input can also produce a result outside the engine's supported range. In that case, the page reports an error instead of displaying an overflow or misleading rounded result. Check units first: enter kW, not W, and do not confuse kVA with kW. If your source lists both quantities, use them as a cross-check rather than treating either as a substitute for the actual equipment requirements.
Worked examples and interpretation
The examples below are arithmetic checks generated from the project's reference fixtures. They show that unity power factor makes the numerical kW and kVA values equal, while a lower factor increases apparent power for the same real power. Each row states the factor used, so the result can be reproduced without a hidden preset. A zero real-power input returns zero for any valid factor. The examples are not typical ratings, design recommendations, or claims about a particular generator or motor. Rounding can make a displayed value look exact even though the inputs themselves may be estimates. Retain extra precision from a trusted source when the result feeds a later engineering calculation. A kVA conversion alone does not account for starting current, duty cycle, ambient conditions, voltage regulation, or the capacity limits of conductors and protective devices. Do not use it as a substitute for a manufacturer's instructions or a code-compliant design. For an AC current conversion, the kW to amps calculator asks for voltage and the needed circuit details. For the reverse apparent-power relationship, use kVA to kW with the relevant power factor. Other unit tools are in the conversion calculator index.
Worked examples
| KW | PF | Result |
|---|---|---|
| 5 | 0.8 | 6.25 kVA |
| 10 | 1 | 10 kVA |
| 4 | 0.25 | 16 kVA |
Common questions
Can I convert kW to kVA without power factor?
No. Real power alone does not determine apparent power in this model. Find a relevant power-factor value from equipment data or a measurement instead of guessing.
Does this result size a generator?
No. It converts the entered values only. Generator selection also depends on load behavior, starting demand, voltage, frequency, operating conditions, and manufacturer guidance.
Limitations
Scope and safe use
This page performs a mathematical conversion only. It cannot determine whether an electrical service, transformer, generator, inverter, or motor is suitable for a particular installation. Equipment selection depends on the actual load profile, transient demand, voltage, frequency, phase arrangement, manufacturer limits, and applicable installation rules. A facility total may not be the simple sum of nameplate values, and a single power-factor figure may not represent every operating state. Confirm the source, units, measurement point, and time period before relying on an input. If the power factor is unknown, stop and obtain reliable equipment documentation or a measurement rather than accepting an assumed default. The form begins without invented values for this reason. Once complete, the server recalculates the submitted values so the page remains useful when scripts are unavailable. The result lists the values used and the relationship applied. It is an educational conversion, not a professional electrical assessment. Seek qualified review before using a result for procurement, installation, protection, or a safety decision.
Sources
Related tools
Cite this page
Wattopedia Editorial Team. kW to kVA Calculator. https://wattopedia.com/kw-to-kva . Updated 2026-10-29.