V = I × R
How to use this calculator
- Pick the quantity you want to solve for.
- Type the other two.
- The card shows volts, amps, ohms, and watts.
- Submit the form if JavaScript is off.
- The same Ohm's law relations run on the server, so the first number is already on the page.
The default is a hypothetical 12 volts across 4 ohms. Current is 3 amps and power is 36 watts: 12 divided by 4 is 3, and 12 times 3 is 36. Those values do not establish a safe resistor, supply or test arrangement. Change the solve-for box to volts or ohms to recover the same relationship from the other two values.
This page is DC. It does not use a power factor, and it does not use the square root of 3. If the circuit is AC, stop here and open the power calculator. A 120 volt heater still follows V = IR in the resistive limit, but a motor does not, and this form will not warn you about that.
Formula
V = I × R
I = V / R
R = V / I
V is volts, I is amps, and R is ohms. OpenStax describes V = IR for ohmic devices and distinguishes devices that do not have a linear voltage-current relationship. Power here is the DC product P = V × I. Neither equation identifies a component's safe operating rating.
Solving for current
Current is volts divided by resistance. A larger resistor at the same voltage draws less current. The default 12 volt, 4 ohm case is 3 amps. The same 12 volts across 8 ohms is 1.5 amps. The table at the bottom of this page is that division at 12 V and 24 V for a set of round resistor values. Every cell is this engine.
Do not type zero ohms. A short is not a number this page can return. Resistance must be greater than zero and not more than 1,000,000 ohms. Volts stay between 1 and 1000, the same window as the other conversion tools on this site.
Solving for volts
Volts are current times resistance. Type 3 amps and 4 ohms to obtain 12 volts. Type 10 amps and 12 ohms to obtain 120 volts. An unsupported result is rejected; the page keeps the submitted inputs and marks the result unavailable instead of presenting a default answer as the result. The supported range is a form limit, not a physics limit.
For another hypothetical check, 0.018 amps through 500 ohms corresponds to 9 volts. This is a relationship among entered values, not a prediction of a battery's loaded voltage, condition or remaining capacity.
Solving for resistance
Resistance is volts divided by current. Type 12 volts and 3 amps to obtain 4 ohms. Type 9 volts and 0.018 amps to obtain 500 ohms and a calculated dissipation of 0.162 watts. Calculated dissipation alone does not establish a safe component rating; temperature, derating and the actual component specifications remain outside this model.
Keep the current in amps, not milliamps, unless you convert first. 18 milliamps is 0.018 amps. Typing 18 with 9 volts would claim 0.5 ohm and 162 watts, which is a different circuit.
Worked example
- In a hypothetical 120 volt, 10 ohm case, the engine returns 12 amps and 1440 watts.
- The steps are 120 divided by 10, then 120 times 12.
- No circuit, conductor, breaker or installation capacity follows from that numerical example.
Change the solve-for box to ohms and type 120 volts and 12 amps. You get 10 ohms back. The trio is the same. The card lists all four numbers so a printed page still shows volts, amps, ohms, and watts together.
Current at 12 V and 24 V
Ohm's law. Every cell is computed by the same function as the result card.
| Ohms | Amps at 12 V | Amps at 24 V |
|---|---|---|
| 1 | 12 | 24 |
| 2 | 6 | 12 |
| 4 | 3 | 6 |
| 8 | 1.5 | 3 |
| 10 | 1.2 | 2.4 |
| 12 | 1 | 2 |
| 16 | 0.75 | 1.5 |
| 22 | 0.5455 | 1.0909 |
| 47 | 0.2553 | 0.5106 |
| 100 | 0.12 | 0.24 |
Amps, milliamps, and one resistor
Type current in amps. 18 milliamps is 0.018 amps. The 9 volt, 0.018 amp case on this page is 500 ohms and 0.162 watts. If you type 18 instead of 0.018, the engine still divides, and you get 0.5 ohm and 162 watts. That is a different circuit. A meter on milliamps does not change the formula. You convert the reading first.
This form is one voltage, one current, and one resistance. It does not add series resistors or combine parallel resistors. If two resistors share a current, add those ohms yourself and type the total. If two resistors share a voltage, the currents add, and this page still wants the one current you care about. Networks belong on paper first. Then type the pair you measured.
The computed values describe the entered ideal model, not a physical test. Real components may change resistance with temperature or behave nonlinearly. This page cannot establish a safe test setup, component rating or measurement procedure.
Common questions
What is Ohm's law?
For an ohmic resistor, voltage equals current times resistance. The cited reference explains the ohmic-device condition. This page independently rearranges that relationship and calculates steady DC power.
How do I find amps from volts and ohms?
Divide volts by ohms. 12 divided by 4 is 3 amps. The default on this page is that case.
Does this work on AC?
Only for a purely resistive load at the RMS values, and even then this form does not include power factor. Use the power calculator for AC.
Why is power on the card?
Because P = V × I is the electrical power relation. This DC calculation is not a substitute for a resistor datasheet or an AC apparent-power calculation.
Where does the wire size come from?
This page does not determine wire size or protective devices. The optional watts-to-amps link is another arithmetic view of the same DC values, not an installation recommendation.
Limitations
This is a calculation aid, not a permit.
The watts-to-amps page starts on DC with these watts and volts. Use it when you want the current at a different voltage. For AC with a power factor, use the power calculator .
Model: one ideal ohmic resistor at a steady DC operating point. Resistance is assumed constant. This form does not model AC reactance, nonohmic devices, temperature changes or component safety ratings. Examples are hypothetical arithmetic, not instructions to energize a circuit.
It does not apply power factor, three-phase or reactance, select a wire or breaker, or determine circuit capacity. Use the power calculator for its stated sinusoidal AC model. Use watts to amps when you know electrical input watts and volts. Search engines should use the clean address of this tool.
Server-rendered results use the values in the request URL. Shared addresses may remain in browser history and server logs. Do not enter confidential information.
It is also not a temperature-corrected resistivity calculation. Resistance here is the number you type, not a copper table at 75 C. For an installation voltage-drop question, see the voltage-drop review guide and have the complete run reviewed by a qualified professional.
The address of a filled-in calculation includes the solve-for choice and the two known values. Search engines should use the clean address of this tool. A filled-in address points its canonical link at the page with no query. The number on the card is the same either way, because the server computes it before any script runs.
Results are rounded to four decimal places. 12 volts on 4 ohms is 3 amps. Other pairs are not whole numbers. The table uses the same rounding. If you need more places for a lab measurement, this page is the wrong instrument. It is built for planning a DC circuit, then handing the watts and volts to the current check.
Keep the assumptions with the number. A current without the volts and the ohms cannot be checked later. Show steps includes those items so a printed page still shows them. The print button hides the menu and the form. The steps stay.
Sources
- OpenStax University Physics Volume 2, §9.4 Ohm's Law. Accessed 2026-10-29.
- OpenStax University Physics Volume 2, §9.5 Electrical Energy and Power. Accessed 2026-10-29.
Cite this page
Wattopedia Editorial Team. Ohm's Law Calculator (Volts, Amps, Ohms). https://wattopedia.com/ohms-law-calculator . Updated 2026-10-28.